Current visitors

Home
Members

jgmo's latest activity

J

jgmo replied to the thread BF75, late model - 6 wire plug at the engine??.

Hi, I definitely don't know but... ...Looking at the shop manuals Honda sells, they list one for: BF75DK3/4...frame number...

May 24, 2026
J

jgmo replied to the thread Is there a way to completely bypass a honda 15 hp bystarter?.

It's a well known fact in the automotive repair world (where I came from before retirement) that the replacement parts "stream" has been...

May 24, 2026
J

jgmo replied to the thread Is there a way to completely bypass a honda 15 hp bystarter?.

Hi, I know of no way, other than your "feed it 12 volts" method, to "bypass the bystarter" auto choke. Although, there is a "manual...

May 23, 2026
J

jgmo replied to the thread Engine Stalling and furl filters are nearly dry?.

Hi, Agree that this could be caused by an pickup tube problem. I've seen them cracked, or with a hole in them and sometimes just...

May 21, 2026
J

jgmo replied to the thread Honda BF90 limp mode issue.

Hi Brad, Yes, pretty strange Indeed. I have to say up front I have never worked on a Honda 90 nor have I ever experienced this problem...

May 17, 2026
J
jgmo replied to the thread How to install water pump housing spacers on a 1985 10 hp b100L.

Hopefully this is what you're looking for? If so, good luck. Found on page 79 of the shop manual.
May 17, 2026
J

jgmo replied to the thread Thread repair.

Your tilt shaft/tube is part number 50381-ZY9-000 See number 18 in the link below...

May 15, 2026
J

jgmo replied to the thread BF 115 2023 Trim up at all Motor cuts off beeps twice continuously.

Hi, I don't know these later model outboards at all. You might want to check oil pressure. I'm pretty sure it should alarm if low but...

May 14, 2026
J

jgmo replied to the thread Thread repair.

You would need to list year and model or horsepower before anyone could answer your last question. Do you have/know the frame number...

May 14, 2026
J

jgmo replied to the thread Honda BF9.9A (4 stroke) Fuel not reaching compression chamber.

Hopefully it doesn't have a limiter and you can just remove the mixture screw and blast carb spray in there. There are two holes on the...

May 13, 2026
J

jgmo replied to the thread Honda BF9.9A (4 stroke) Fuel not reaching compression chamber.

If that one has a limiter cap and you try to remove it, you might break off the top of the mixture screw. It was made to snap off (thank...

May 13, 2026
J

jgmo replied to the thread Honda BF9.9A (4 stroke) Fuel not reaching compression chamber.

Yeah, if spark jumps from the plug wires, change them! Aa far as the carb goes, you may not have cleaned it as well as you think you...

May 12, 2026
J

jgmo replied to the thread Thread repair.

Hi, Just my opinion, but I would opt for replacement. It's kinda/sorta like a lifeline... ...if it fails at a critical moment...

May 12, 2026
J

jgmo replied to the thread Honda BF9.9A (4 stroke) Fuel not reaching compression chamber.

Those voltage readings look pretty low. Are you using the AC volts scale on your meter? Did you try checking the pulser coil voltage...

May 11, 2026
J

jgmo replied to the thread Honda BF9.9A (4 stroke) Fuel not reaching compression chamber.

Forgot to mention that, since this is a "waste spark" ignition where both plugs fire together every time, you should leave one plug...

May 11, 2026

Show older items

Home
Members

Top