Logo
FULL SITE MENU

Search results

  1. Garygin

    Hond 225 3950 max rpm

    Hi Jgmo! Well thanks for doing all of that research. It sounds like I have a few more things to check. The vacuum tank I’m most curious about. I really don’t know if it is getting vacuum, and if it is holding vacuum. The next I was going to check was is it getting vacuum. I was away so Ii...
  2. Garygin

    2004 BF225 25" extension case driveshaft bearing (bushing) question

    Great . Feels good when you accomplish something like that
  3. Garygin

    Hond 225 3950 max rpm

    Thanks Chawk. I did re adjust all of that when I put new throttle and shift cables on
  4. Garygin

    Hond 225 3950 max rpm

    Well I ran it in a tank of water today . 3950 rpm and the same thing. Just like a rev limiter. Any suggestions would be very much appreciated. Gary
  5. Garygin

    Hond 225 3950 max rpm

    Chawk. Thanks for your input. It is always appreciated. If you remember I posted pictures of a vacuum diaphragm I had modified To fit since you cannot purchase one from Honda. So that is new. I Have replaced almost everything. Jgmo . Whatever you find please let me know. The service manual is...
  6. Garygin

    Hond 225 3950 max rpm

    I haven’t finished it … grandkids came over. I have it almost done. I did notice that the service manual shows two different routing for the vacuum lines . The schematic on boats.net looks like the right one . I do have the unrestricted vac. hose hooked up correctly. I’m wondering if the IAB...
  7. Garygin

    Hond 225 3950 max rpm

    Ok, I followed your instructions line by line. You won’t believe this. I found one of my test leads was bad. Used a different one everything is working . I wasted so many hours I don’t even want to tell you. Thank you! One other question. When I took this apart yesterday I noticed when I had it...
  8. Garygin

    Hond 225 3950 max rpm

    Thanks so much. I’m am looking at it right now. One question why would I see voltage drop when I check the terminal that feeds the hp fuel pump in the 2 second test. I never had 12volts. First it was 6 then later in the day I checked it again and it was .6. I did use a good ground when checking...
  9. Garygin

    Hond 225 3950 max rpm

    Ok I ready to jump off a frieking bridge. First I just replaced ALL the fuel filters. New fuel tank, new IAB vacuum diaphragm , new fuel line cut solenoid valve. I just rebuild the whole out drive , service bulletin #56 , all gaskets seals bearings , water pump, and checked every fuel line, and...
  10. Garygin

    2006 Honda BF225 - Head Gasket? vids attached

    I stand corrected. I must have entered the incorrect part number. That is what I replaced as shown in the picture I posted
  11. Garygin

    2004 BF225 25" extension case driveshaft bearing (bushing) question

    I know the manual doesn’t say anything about packing with grease. One the case is filled with gear it wouldn’t make any difference the oil will wash out the grease. FYI I ran my boat for the first time on Friday . I had no issues at all and I did not pack them. I did hose the down with gear oil...
  12. Garygin

    2004 BF225 25" extension case driveshaft bearing (bushing) question

    Ok I just looked at my pictures. Here’s what I did. You don’t really need the bearing puller . If you can get a piece of tubing that has a big enough I.d. To go over the shaft so the inner race rests on it and the other end on the table of your press. This is what I did and it worked great. If...
  13. Garygin

    2004 BF225 25" extension case driveshaft bearing (bushing) question

    I just looked at the service manual. I’m assuming you are working on the propeller shaft? Hey feel free to call me if like. 484 883 7414
  14. Garygin

    2004 BF225 25" extension case driveshaft bearing (bushing) question

    Ok, first I love S. Carolina. But it’s a little far for me. lol. What bearing is it exactly, so I can be on the same page as you. If the bearing is on a shaft you only want to heat the inner race ONLY! If you heat everything it will defeat the purpose. Keeping it in the freezer really isn’t...
  15. Garygin

    2004 BF225 25" extension case driveshaft bearing (bushing) question

    I’m really surprised. Now if some idiot used loctite bearing mount you will have difficulty removing the bearing.where are you located? I’m retired . If you live within a reasonable distance I would be more than happy to give you a hand
  16. Garygin

    2004 BF225 25" extension case driveshaft bearing (bushing) question

    Hey scubagrog. FYI. When you remove the bearings use your heat gun they will come real easy. You don’t have to get them real hot. You should almost be able to hold your hand on it. Also press on the inner race when putting the new ones on. The needle bearing comes with a plastic sleeve to keep...
  17. Garygin

    Exhaust manifold modification BF 225 and BF 200

    Hi , I just tried to get Honda to cover service bulletin 56. I had to call a Honda service center and they submitted the request directly to Honda . It was denied. My engine is a 2002 that was sold new in 2004 . It has 600 hours on it. You can call any Honda dealer and if the service bulletin...
  18. Garygin

    BF225 Lower unit shift shaft removal

    I totally agree. It would be much faster and cheaper. Like you said swap out the propeller assembly and buy a new prop. Changing the prop assembly is easy. Gary
  19. Garygin

    BF225 Lower unit shift shaft removal

    I agree with the link you posted. The load would on the reverse bearing and gear. I have built many gear boxes . Been a machinist for 53 years . I would not attempt it. If you go to a GOOD machine shop and they know what they are doing it could be cut and welded in the correct direction. If you...
  20. Garygin

    2004 BF225 25" extension case driveshaft bearing (bushing) question

    I used to dive a lot . Mostly out of Indian River inlet in Delaware
Back
Top