Logo
FULL SITE MENU

Search results

  1. S

    Johnson Evinrude 115 hp model J115PXSOR

    Hi y’all my engine dies out at low idle..a lot if I control it from under the hood it is fine. I would just like to set the idle up a little about the thickness of a razor blade it isnt much but I don’t need a whole lot going to try to add a photo wondering if this is where I can set idle up a...
  2. S

    2005 Johnson 115 hp 2 stroke dies easily at low idle

    Thanks for the reply, good stuff. I can use these ideas
  3. S

    Fuel type 2005 Johnson 115 hp 2cycle

    Thanks yeah don’t have an owners manual. I guess I was just curious if everyone uses a mid grade or higher fuel type and I meant 85 octane not ethanol just to be clear.
  4. S

    2005 Johnson 115 hp 2 stroke dies easily at low idle

    I am not sure how to advance the idle and don’t have a timing light. But I think if I raised the idle just a tad it wouldnt always be dying while trying to maneuver slowly like when trying to to load onto trailer or floating slowly in toward a dock. Having to restart several times during slow...
  5. S

    Fuel type 2005 Johnson 115 hp 2cycle

    Got it thanks.
  6. S

    Fuel type 2005 Johnson 115 hp 2cycle

    Could you expand on that ? Why?, and or what should be used instead ? This is the fuel offered everywhere.
  7. S

    Fuel type 2005 Johnson 115 hp 2cycle

    How many use the e85 fuel in this motor
  8. S

    Scuppers

    Yeah those scuppers are factory height and yes I am changing the hatch so it has a better seal That hatch, to me, appears to have been added post factory. Somebody wanted an easier access to the bilge maybe. I was just hoping scuppers that everyone has on their boat were of different degrees of...
  9. S

    Scuppers

  10. S

    Scuppers

    Yes they let water out of the well while underway and then supposed to stop water while sitting still.
  11. S

    Scuppers

    These allow a lot of water into the well
  12. S

    Scuppers

    I always have trouble with loading photos here I don’t think it works well
  13. S

    At My Wits End: Lower Unit Seals (Shiftshaft/Driveshaft) Replaced, But Still Seeing Leaking Fluid!

    You also could get seepage if the seal shaft had been nicked while getting the seals installed.
  14. S

    Scuppers

    I have the type with the little ping pong ball in them they don’t seal off water worth a darn and allows the well to take water which in turn goes under a hatch to the bilge pump. Constant cycling water. I think it cannot be stock to have a hatch in a water well anyway but there it is bad seal...
  15. S

    Motor tilt intermittent

    weird won’t always work and if it starts to act like it won’t lift hittin up/down lever quickly seems to make a difference. Will low Hydralic fluid in the pump cause that? Sometimes it will groan while lifting. Seems like it works 90% of the time. The ten percent is at the ramp or in low water...
  16. S

    Steering difficult 2005 evinrude 115 hp on a 96 winner CC

    But I am going to try that to see if it changes appreciate the suggestion
  17. S

    Steering difficult 2005 evinrude 115 hp on a 96 winner CC

    I don’t believe it’s pulling to one side where it needed adjustment. Thanks for the rrply
  18. S

    Steering difficult 2005 evinrude 115 hp on a 96 winner CC

    Weird thing steers easy to the right and hard to the left. All grease been done. Unless you are at idle and then both are easy
  19. S

    2005 Johnson 115 hp 2 stroke. Identify a bolt?

    Ok I changed gauges and mounted in a different spot that had I/8 tapered threads and no bolt in it and it works. The gauge reads high according to my heat sensor gauge it has the motor at idle about 140 the boat gauge said 220. So the gauge is not calibrate but I can do that math. And so now...
  20. S

    2005 Johnson 115 hp 2 stroke. Identify a bolt?

    I didn’t have an opportunity to do that Thursday so it will be tomorrow be for I get it in. But will post here as to how it goes.
Back
Top