Logo
FULL SITE MENU

Search results

  1. G

    Shift rod

    On the throttle shift linkage leading to the shift rod. Called a shift arm link I believe. I have to try again at 22.06 as the bolt pin was hanging up not allowing shift rod to come up far enough. Nothing was working so must make that adjustment as a last effort. Had lower unit off half a dozen...
  2. G

    Shift rod

    So, a couple of things. No reverse on water. So have to try again using other measurement. That set screw must have made linkage to jam when I first tried at 22.6. But then I forgot to add cotter key on linkage and it fell off and when i put extra push on, it broke one piece of linkage. I...
  3. G

    Shift rod

    After several tries I got it. I found that the linkage at top of rod was hanging up on set screw in the rod top. I went back to my manual and reset it at the 21.06 and finally I have both forward and reverse. My 79 manual was correct. Seloc was wrong. I can’t explain except to say I now can get...
  4. G

    Shift rod

  5. G

    Shift rod

  6. G

    Shift rod

    Got it. Look carefully, no choke plate on upper carb in manual.
  7. G

    Shift rod

  8. G

    Shift rod

    Maybe only 79, maybe they added that choke plate in 80???
  9. G

    Shift rod

    I have same picture of intake parts in the manual minus the butterfly in upper carb. Unable to send you the picture in my manual. Have not figured out how to do it yet. 🤷
  10. G

    Shift rod

    I have a manual printed in 1978 titled 79 v6 only 150-235 hp by evinrude. The rod and butterfly from a 79 v4 100hp fit in perfectly because of matching numbers on both carbs. All I can do is shrug my shoulders. IDK. I will look at what you sent.
  11. G

    Shift rod

    I can’t send a picture, I’t just won’t send. Says that picture to big.
  12. G

    Shift rod

    No it has the original electric/manual choke on it. My 90hp had primers of which were handy. Like I said, my 79 manual shows no choke on upper carb. I tried to send picture but my phone wouldn’t send. I will try iPad that I just purchased.
  13. G

    Shift rod

    Yes, bare rod, no threaded holes. I was surprised but I had parts I needed from a Johnson 100 hp of same year. One thread I read said the same about the hard starting. And a picture in my 79 manual shows no butterfly. New to me also, but why?? Strange.
  14. G

    Shift rod

    I won’t know until tomorrow or thursday but I believe I will have it. I will take two carbs off so I can reach it better. I solved hard starting by adding a choke butterfly to upper carb. It started up and in seconds was idling perfectly. Starter was clean and brushes in good shape. Pistons...
  15. G

    Shift rod

  16. G

    Shift rod

    Correction: I must add .46 inch not .64 dah!
  17. G

    Shift rod

    Thanks for q & a: I set like in dangar video, from top of gear case to hole, in neutral at 21.6 as found in 79 evinrude manual for the 150,175, 200,235 only. Mine is the 150949. The rod was bent that I replaced with new shift rod ordered by model number. It would not go into reverse when I...
  18. G

    Shift rod

    Installed shift rod to specs in 79 manual for model 150949-1979 v6 150 evinrude motor. No reverse! Checked two manuals and seloc manual was different than an original 79 manual by .64 inch (11.7mm or 1.168cm). Is seloc manual right? I tested shift before putting LU back on and had R N F. I...
  19. G

    Plugs and gas

    Thanks. I received a evinrude factory service manual today in mail. In very good shape! The binding was like new. Just on the 79 v6 150-235 hp.
  20. G

    Plugs and gas

    I Need confirmation on: 79 v6 150hp-two model numbers. 150940 and 159949. Is the only diffence in the lower unit length. With the 940 being the longest.
Back
Top