Logo
FULL SITE MENU

Search results

  1. P

    1984 Evinrude 30 OK?

    Evinrude E30ECRR, Ser. F036841 Just rebuilt the water pump for the second time in the last 2 weeks because of previous errors on my part. It's been 5 years since the last rebuild, so I'm not sure what the lower unit should look like on the muffs. These photos are with the engine off and the city...
  2. P

    Fuel Line or Fuel Pump?

    Uh, um, well... let's just say it runs fine when you put the fuel inlet and output lines on the correct fittings on the fuel pump...
  3. P

    Fuel Line or Fuel Pump?

    Did some tracing. No fuel in the carb bowl. Fuel definitely getting to the new (not rebuilt) fuel pump I just put in, but no further.
  4. P

    Fuel Line or Fuel Pump?

    Different tank and hose, same result. I pump the bulb until it's firm. Start the engine and it runs 10-15 seconds, then dies. Won't restart. When I disconnect the hose at the motor, it sprays all over. I've had the pontoon/engine since 2009 and it's always run like a champ. This year it's making...
  5. P

    Fuel Line or Fuel Pump?

    Will do. Thanks.
  6. P

    Water Pump No Go

    Thank u for replying. Using ear muffs with the hose on wide open. I only run the engine at idle. This setup has worked well in the past.
  7. P

    Water Pump No Go

    1984 E30ECRR Ser. F036841 Sorry to be posting so much. This has been a lousy start to the season for my boats. Rebuilt the water pump on this engine and it does not appear to be moving water. Haven't been able to get the engine going but for 10 seconds or so, but I've disconnected the hose from...
  8. P

    Fuel Line or Fuel Pump?

    1984 E30ECRR Ser. F036841 Just installed a brand new Sierra fuel pump. Hooked up the fuel line and it took about 10 pumps to get a firm bulb. Engine started right up but wouldn't run but a few seconds. The fuel line is old. Any way to diagnose the problem before playing Guess Which Part? Many...
  9. P

    1984 Evinrude 30 Uh-oh

    It worked! New stud embedded in LB Weld Steel holding strong.
  10. P

    1984 Evinrude 30 Uh-oh

    1984 E30ECRR Ser. F036841 The stud on the carburetor end of the engine that holds the starter bracket snapped. Even with the other two bracket bolts in place, the flywheel kicks the starter away, preventing it from engaging. Miraculously, I've found the OEM part at a local shop. I have made a...
  11. P

    Evinrude Dirty 30

    Yep. Many thanks for your help. Picking up Super Clean now 😀
  12. P

    Evinrude Dirty 30

  13. P

    Evinrude Dirty 30

    Sorry. Just went out and took a picture. There's a hole underneath the carburetor. Then I looked at the bottom of the steering column to see another hole. I guess that's where the column drains? I would show u the pic, but apparently I have to have a separate photo account to post an image, and...
  14. P

    Evinrude Dirty 30

    Thanks! Where does all the water that goes down the holes in the floor of that area end up?
  15. P

    Evinrude Dirty 30

    1984 E30ECRR SER. F036841 Just rebuilt a leaky carb that messed up the floor of the engine compartment. What's the best way to clean up that area. Thanks for your help. PW
  16. P

    84 Evinrude Fountain Display

    Yep. That's the way I put it back in. But it might have slipped out.
  17. P

    84 Evinrude Fountain Display

    Aftermarket kit by Sierra. I've used these before with no trouble.
  18. P

    84 Evinrude Fountain Display

    1984 E30ECRR Ser: F036841 I usually post this. Sorry. No leftover parts. The most difficult part of the reassemble is reinserting the feed tube from the pump to the power head. I may have gotten that wrong. I loath taking it apart again.
  19. P

    84 Evinrude Fountain Display

    Just rebuilt the water pump and hooked up the earmuffs. When I turn on the water, it's pouring out of the weep holes in the gear case. Don't recall it doing this before. Wha'd I do wrong? Many thanks for your help, PW
  20. P

    Mercruiser Injectors Not Injecting

    Ding Ding Ding! Your diagnosis was spot on! Scroll to the end of the thread to see how it worked out. If by the IC you mean the connector at the bottom of the distributor under the cap that has two connectors on the outside and hooks up to the pickup coil on the inside, no. In an earlier post...
Back
Top