Quicksilver Marine Parts Catalog
- Contents
- Pre-1988 Mariner
- Mercury & Mariner
- Carburetor Kits
- Fuel Pump Repair Kits
- Ignition Keys
- Ignition Parts (2-Stroke)
- Ignition Parts (4-Stroke)
- Lower Unit Gearcase Seal
- Pistons
- Oil Filters
- Powerhead Gasket Sets
- Rod Main Bearings
- Solenoid Relay (2-Stroke)
- Solenoid Relay (4-Stroke)
- Spark Plugs (2-Stroke)
- Spark Plugs (4-Stroke)
- Stators
- Thermostat Kits
- Water Pump Parts (2-Stroke)
- Water Pump Parts (4-Stroke)
- Mercruiser
- Engine Parts
- View All »
- Alternators
- Camshafts, Bearings, Lifters & Push Rods
- Carburetors
- Connecting Rod Bearings
- Crankshaft Bearings
- Distributor Assembly & Components
- Distributor Gears
- ECMs, Coils, Wires & Spark Plugs
- Engine Couplers
- Engine Gaskets
- Exhaust Manifolds & Elbows
- Flame Arrestors
- Fuel Coolers
- Fuel Injection Components
- Fuel Pumps & Filters
- Ignition Tune-up Kits
- Intake & Exhaust Valves
- Oil Coolers
- Oil Pumps & Components
- Piston Rings
- Pistons
- Rocker Arms & Hardware
- Starter Parts
- Starters & Solenoids
- Thermostats, Housings & Covers
- Timing Chains & Gears
- Valve Caps, Springs & Keepers
- V-Belts & Serpentine Belts
- Water Hoses—Engine Supply
- Water Hoses—Exhaust Cooling
- View All »
- Transom & Drive Parts
- View All »
- Bearing Carriers
- Bellows
- Drive Shaft Housing & Sterndrive Units
- Drive Shaft Housing Bearings
- Drive Shaft Housing Gears
- Gear Case Bearings
- Gear Case Gears
- Gear Case Seals
- Gear Case Shafts
- Gear Case Shims
- Gimbal Bearings
- Installation Gaskets
- Trim Cylinders
- Trim Cylinder Hardware
- Trim Cylinder Hoses
- Universal Joints (U-Joints)
- Water Pump Impellers & Kits
- View All »
- Engine Parts
- Page Numbers
ENGINE ACCESSORIES
ENGINE ACCESSORIES
HEX NUT
OUTBOARD MOUNTING HARDWARE
Used for permanent mounting of an engine to the boat transom.
MOUNTING BOLT
Hex Nylock Nut, brass
Fits current Mercury/Mariner 40 hp. thru V‑6 outboards (2‑cycle and FourStroke),
and also fits Force 40‑120 hp. outboards (USA 0E009500 and Newer). Also
shipped standard with the 135‑275 hp. Verado outboard.
Standard 4 1/2" Length Mounting Bolt (2.25 in. thread)
Fits current Mercury/Mariner 40 hp. thru V‑6 outboards (2‑cycle and FourStroke),
BLOW START SIPHON
and also fits Force 40‑120 hp. outboards (USA 0E009500 and Newer). Furnished
standard with the 135‑175 hp. Verado outboards.
BLOW-START SIPHON
MOUNTING BOLT
The ruggedly constructed siphon is a quick and convenient way to transfer fuel
from a gas can to a fuel tank. The siphon flows approximately five gallons of fuel
Optional 6 1/2" Length Mounting Bolt (2.75 in. thread)
per minute. Siphoning is started by blowing air into a blow‑tube. Even better, it
Fits current Mercury/Mariner 40 hp. thru V‑6 outboards (2 cycle and 4‑Stroke), and
eliminates the old "fuel‑in‑the‑mouth" possibility and stores easily. The siphon is
also fits Force 40‑120 hp. outboards (USA 0E009500 and Newer).
very useful in areas where boat fuel is no longer available at the dock.
Quicksilver Branded, Peg Display Product Point of Sale Packaged.
FLAT WASHER
Stainless Steel x 1.50 in. OD
Fits current Mercury/Mariner 40 hp. thru V‑6 outboards (2‑cycle and FourStroke),
and also fits Force 40‑120 hp. outboards (USA 0E009500 and Newer). This is also
the "inner" washer furnished with the 200/225/250/275 hp. Verado outboard.
Priced individually, sold @ multiples of 5
716