Quicksilver Marine Parts Catalog
- Contents
- Pre-1988 Mariner
- Mercury & Mariner
- Carburetor Kits
- Fuel Pump Repair Kits
- Ignition Keys
- Ignition Parts (2-Stroke)
- Ignition Parts (4-Stroke)
- Lower Unit Gearcase Seal
- Pistons
- Oil Filters
- Powerhead Gasket Sets
- Rod Main Bearings
- Solenoid Relay (2-Stroke)
- Solenoid Relay (4-Stroke)
- Spark Plugs (2-Stroke)
- Spark Plugs (4-Stroke)
- Stators
- Thermostat Kits
- Water Pump Parts (2-Stroke)
- Water Pump Parts (4-Stroke)
- Mercruiser
- Engine Parts
- View All »
- Alternators
- Camshafts, Bearings, Lifters & Push Rods
- Carburetors
- Connecting Rod Bearings
- Crankshaft Bearings
- Distributor Assembly & Components
- Distributor Gears
- ECMs, Coils, Wires & Spark Plugs
- Engine Couplers
- Engine Gaskets
- Exhaust Manifolds & Elbows
- Flame Arrestors
- Fuel Coolers
- Fuel Injection Components
- Fuel Pumps & Filters
- Ignition Tune-up Kits
- Intake & Exhaust Valves
- Oil Coolers
- Oil Pumps & Components
- Piston Rings
- Pistons
- Rocker Arms & Hardware
- Starter Parts
- Starters & Solenoids
- Thermostats, Housings & Covers
- Timing Chains & Gears
- Valve Caps, Springs & Keepers
- V-Belts & Serpentine Belts
- Water Hoses—Engine Supply
- Water Hoses—Exhaust Cooling
- View All »
- Transom & Drive Parts
- View All »
- Bearing Carriers
- Bellows
- Drive Shaft Housing & Sterndrive Units
- Drive Shaft Housing Bearings
- Drive Shaft Housing Gears
- Gear Case Bearings
- Gear Case Gears
- Gear Case Seals
- Gear Case Shafts
- Gear Case Shims
- Gimbal Bearings
- Installation Gaskets
- Trim Cylinders
- Trim Cylinder Hardware
- Trim Cylinder Hoses
- Universal Joints (U-Joints)
- Water Pump Impellers & Kits
- View All »
- Engine Parts
- Page Numbers
EXHAUST SYSTEM
EXHAUST ELBOW
EXHAUST ELBOW
4 inch (102 mm) O.D., 7 degree down angle, hot dipped & powder painted
3 inch O.D., 0 degree down angle
Fits 2002‑2004 MCM GM V‑6 & V‑8 (305, 350 & 377 cid) engines with dry joint
Fits MIE GM V‑8 engines with center rise outlet exhaust manifold
exhaust manifold (s/n 0M600000‑0W309999)
EXHAUST ELBOW
EXHAUST ELBOW
Standard elbow.
4 inch (102 mm) O.D., 14 degree down angle, Hot dipped & powder coated
Fits MCM 496 Mag & MIE 8.1L engines; also MCM 8.2L Mag (non‑EC) engines
Fits 2004 and newer MCM GM V‑6 & V‑8 (305, 350 & 377 cid) engines with dry
joint exhaust manifold (s/n 0W310000 and up); also fits 2002 and newer MIE GM
EXHAUST ELBOW
V‑8 (350 & 377 cid) engines with dry joint exhaust manifold (s/n 0M317000 and up)
EXHAUST ELBOW
Design II
Standard elbow for EC engines
Fits MCM 496 Mag & MIE 8.1S EC engines, also MCM 8.2L Mag EC & MIE 8.2L
Port side, standard rise
EC engines
Fits 2008 and newer MCM/MIE GM V‑6 & V‑8 (305, 350 & 377 cid) EC engines
EXHAUST ELBOW
EXHAUST ELBOW
This elbow is 2 in.(51 mm) higher than the standard elbow.
Starboard side, standard rise
Fits MCM 8.1L & 8.2L non‑EC engines
Fits 2008 and newer MCM/MIE GM V‑6 & V‑8 (305, 350 & 377 cid) EC engines
US Quicksilver Product Guide
911