Logo
FULL SITE MENU
Jerryjerry05

Jerryjerry05

Outstanding Contributor From Sebastian ,Fl
Joined
Last seen
Messages
3,518
Reaction score
0

Latest activity Postings About

    • Jerryjerry05
      Jerryjerry05 replied to the thread 1990 Force 120hp Powerhead Removal.
      The black tube is an equalizer tube. Should be 2 of them. They go in the back of the rear cover, they fit in 2 holes and keep the water...
      • 1716195443087.png
    • Jerryjerry05
      Jerryjerry05 replied to the thread Chrysler force 85.
      The water/exhaust should come out of the snout on the bottom of the cavitation plate. There's a hole, maybe 2 in the cover for the mid...
    • Jerryjerry05
      Jerryjerry05 replied to the thread 1990 Force 120hp Powerhead Removal.
      You need 5 posts to add pics. There's a gasket on one part but not the other. Use silicone where there's no gasket. Find the parts...
    • Jerryjerry05
      Jerryjerry05 replied to the thread Chrysler force 85.
      If you have a Chrysler?? Then maybe someplace on the lower part of the cowl is a small metal ID tag with the year and model and serial#...
    • Jerryjerry05
      Jerryjerry05 replied to the thread 1988 FORCE 50 507X8C Junk?.
      The Force 50 is the same as a Chrysler 50 it's a good running motor and can last a very long time if it's taken care of. The bad rap...
    • Jerryjerry05
      Jerryjerry05 replied to the thread 1988 FORCE 50 No water.
      IF??? the last time you used the boat was 2-3 years ago, the exhaust could be clogged with bugs and their nests. Wasps build mud nests...
    • Jerryjerry05
      Jerryjerry05 replied to the thread Gamefisher 7.5 Spark on one cylinder.
      If you have points then you have coils and condensers. My guess is that the condenser or coil is bad. Try switching these around like...
    • Jerryjerry05
      Jerryjerry05 replied to the thread 50 Force won’t start need help.
      Like Racer said: take it to a shop(if they will work on it). I use a BIGGGG 3 jaw puller and a 3# hammer. Loosen the nut, don't remove...
    • Jerryjerry05
      Jerryjerry05 replied to the thread 1986 85hp force not firing on cylinder 3.
      http://www.outboardignition.com/. They have trouble shooting procedures for your motor. If it didn't run full speed before?? Do a...
    • Jerryjerry05
      Jerryjerry05 replied to the thread 50 Force won’t start need help.
      Double check and then take the flywheel off and check the key. Getting the flywheel off isn't going to be easy, Google Flywheel removal...
    • Jerryjerry05
      Jerryjerry05 replied to the thread 50 Force won’t start need help.
      You test the spark on all the plugs?? On the front of the motor is a tab with a line. On the flywheel is 2 sets of scribed lines. One...
    • Jerryjerry05
      Jerryjerry05 replied to the thread 50 Force won’t start need help.
      Might need 5 posts to be able to add pics. Until then use a photo sharing site like Shutterfly or something else. If you have the choke...
    • Jerryjerry05
      Jerryjerry05 replied to the thread 50 Force won’t start need help.
      IF??? it ran for 2 seconds then quit. It's possible it sheared the flywheel key. Really need to know the year. Somewhere on the block...
    • Jerryjerry05
      Jerryjerry05 replied to the thread Two working marine engines.
      What kind? Figure out the brand and repost in that section. There's no Force/ Chrysler with 200 or inboards.
    • Jerryjerry05
      Jerryjerry05 replied to the thread 1992 Force 150 hp overheating.
      On the muffs: needs LOTS!!!!! of water pressure. Get a temperature gun and check the temp as it runs and see if it is really getting as...
    Show older items
  • Loading…
  • Loading…
Back
Top