Logo
FULL SITE MENU

Recent content by muskyking

  1. M

    1996 Evinrude E20CREDA 20 hp Outboard lower end started leaking some oil gasket kit needed

    comming from the prop , i mixed the gas oil 50-1 and it does smoke i think to much so i cut it back a bit on oil, put after taking the prop off it still drips oil and running the motor in a barrel iv never had oil on the top of the water like that before. the next issue i got is from what i see...
  2. M

    1996 Evinrude E20CREDA 20 hp Outboard lower end started leaking some oil gasket kit needed

  3. M

    1996 Evinrude E20CREDA 20 hp Outboard lower end started leaking some oil gasket kit needed

    thankyou so this is the 1 i need correct? 396351
  4. M

    1996 Evinrude E20CREDA 20 hp Outboard lower end started leaking some oil gasket kit needed

    Anyone. when i search the model E20CREDA it says no matchs found
  5. M

    1996 Evinrude E20CREDA 20 hp Outboard lower end started leaking some oil gasket kit needed

  6. M

    1996 Evinrude E20CREDA 20 hp Outboard lower end started leaking some oil gasket kit needed

  7. M

    1996 Evinrude E20CREDA 20 hp Outboard lower end started leaking some oil gasket kit needed

    i took the prop off and started it and it looks like some oil is comming from there so i think all i need is the o ring correct? can someone help me find one i dont need the hole gasket set just the o ring and im trying to search a how too on removing it .
  8. M

    1996 Evinrude E20CREDA 20 hp Outboard lower end started leaking some oil gasket kit needed

    do you know what gasket repair kit i need if i need to change it.
  9. M

    1996 Evinrude E20CREDA 20 hp Outboard lower end started leaking some oil gasket kit needed

    i got oil in my barrel but not sure if it,s comming from the exhust or not,im have ideal issues and its smoking alot at 50.1 ratio , so im in canada so i put 20liters of gas to 400 mils of oil .
  10. M

    1996 Evinrude E20CREDA 20 hp Outboard lower end started leaking some oil gasket kit needed

    1996 Evinrude E20CREDA 20 hp Outboard lower end started leaking some oil started leakeing in the barrel when i was testing the idal today i need the correct gasket kit to repair it. and a diagram if there is one. thanks
  11. M

    1996 EVENRUDE 20HP HELP NEEDED

    thanks.
  12. M

    1996 EVENRUDE 20HP HELP NEEDED

    i need the repaire kit gaskets and o ring can i get directed to tthe corret one , thanks
  13. M

    1996 EVENRUDE 20HP HELP NEEDED

    So iv been reading and A.I said this- For your 1996 20 hp 2-stroke EvinrudeOn this 20 hp engine, the mechanical idle speed is not adjusted by a screw pushing on the carburetor butterfly. Instead, it is controlled by a stop screw on the ignition timing linkage. [1] side of the engine block...
  14. M

    1996 EVENRUDE 20HP HELP NEEDED

    what is the difference between desired idle speed and basic, if i turned the knob on the throttle to much will that make it stall and run rough?
  15. M

    1996 EVENRUDE 20HP HELP NEEDED

    Ok i re,did the carb and started it it ideled not to bad then it started to die i played with the idel, but i also turned the knob on the end of the throttle what is that for is that also for the idel, becauser now the motor is kicking and dies fast?
See more
Back
Top