Logo

1990 120 VRO looper J120TLESB no spark on #4 and can't find tach signal

SaltyScot

Regular Contributor
I got this motor recently and replaced the water pump. It has great compression: 125 on all 4. I took it out and it ran very smooth, but only got my 17' Glasply up to 36mph. So I knew it was probably down a cylinder. Found out it was #4. I found that there is no signal to the coil from the power pack. Is there a way to test the trigger? Or just buy a new power pack since that's often the issue with these V4s?

Also, I can't get my tach to work. There is no gray wire coming out of the control box, so I tried running a wire from the terminal block gray and yellow/gray to no avail. The tach does move super slightly when powered up, but doesn't change when the motor is started. I suppose I could have a bad tach, but where should I be able to pick up the signal at? Thanks.

Stephen
 
Yes, you can test the trigger. Don't buy the pack yet.

Pull the timer base plug at the pack and ohm each of the four windings against the others. They should all read close to the same. An open one or a big outlier tells you plenty, and you don't need the book number to see that.

One thing though. A plain meter on the coil primary won't show you much on these. It is a capacitor discharge pulse, very short. You need a peak reading adapter to catch it. With a regular voltmeter it looks dead even when it is fine. What did you use when you decided nothing was coming out of the pack?

Cheap test first. Move the #4 coil into the #2 hole and take the primary leads with it. If the dead hole moves with the coil, it is the coil or the boot. If it stays on #4, it is upstream. I have also been fooled by a crusty coil mounting face on the block. That face is the ground for the coil. Clean it and try again.

The pack is two separate circuits in one box, one per bank. #2 and #4 are the same bank. So if #2 fires and #4 does not, the charge coil feeding that bank is probably fine and you are looking at the trigger winding or that channel in the pack. I could be wrong, but that is how I would narrow it down.

On the tach. Gray at the terminal block is the send from the rectifier. If there is nothing there while it is running, the rectifier is the first suspect, not the gauge. A tach that only twitches at key on and never moves after that is usually getting no pulses at all. Check the rectifier ground and the two stator leads going into it. Do you have a known good tach you can clip on just to rule the gauge out?

Both faults at the same time make me look at the stator. Pull the flywheel cover and look at the potting. Any brown burn marks, or that hot varnish smell?

Thanks.
 
What I did was move the #4 lead to #2 coil and then there was no spark on #2. I swapped the coils and plug wires too just for fun. The fault always follows that #4 primary from the pack. If I ohm test the trigger with DVA adapter on my Fluke, would that be with the motor off or cranking? Is the DVA adapter necessary for resistance tests? I will definitely check out the rectifier. I have found some corrosion on some of the bolts. I do have another tach I can steal from a different boat. Thanks Miles.
 
I pulled the timer base plug and tested the 4 leads against themselves and every combination gave me between 220-225 ohms. So nothing out of "range" there. I couldn't find my DVA adapter yet, but I was under the impression that that is only for when the motor is running.
 
I'm not seeing a ground for the rectifier. Does it ground to the block by contact? Oh wait, I see a gasket now so maybe not block contact.
 
Last edited:
Well, I have SOME good news to report. I pulled the PP and all the bolts from the rectifier and ignition coils. They came out looking like they had thread lock or something on them they were so corroded. I cleaned up the bolts and bolt holes with tap and die. I ohm tested all the stator and trigger wires and they came out fine. I put everything back together and I still don't have spark on #4. BUT I GOT THE TACH TO FIRE. The original one that didn't register before. Any more ideas?
 
I pulled the PP and all the bolts from the rectifier and ignition coils.....they were so corroded. I cleaned up the bolts and bolt holes with tap and die. I ohm tested all the stator and trigger wires and they came out fine. I put everything back together and I still don't have spark on #4. BUT I GOT THE TACH TO FIRE. The original one that didn't register before. Any more ideas?
Miles has given solid advice. Have you run all the ignition tests listed in the CDI Electronics Troubleshooting Guide?
 
Back
Top