Logo
FULL SITE MENU

Search results

  1. Garygin

    Honda 225 max rpm 3500

    Actually I downloaded it . It is much better than the shop manual
  2. Garygin

    iab vacuum diaphragm

    Ok . I have a 2002 225 hp. Runs great up to about 3700. Can’t get anymore out of it. Changed all filters , compression 200 on all cylinders on a cold engine, checked all plugs. So chawk_man… who always has the best info suggested to check the Iab vacuum diaphragm. Plunger moves freely. If you...
  3. Garygin

    Honda 225hp Vertical Shaft Damaged

    I know this is an old post, but there are several ways to fix this and job weld isn’t one of them .#1 you could have it metal sprayed and turn it back to size . Excellent results and not very expensive considering the cost of a new shaft. 2nd I would turn the shaft make a sleeve and press it on...
  4. Garygin

    BF225 midsection driveshaft bearing/bushing

    I know these are old posts, but I pulled mine out today. I have a 2002 225. The shaft has a little wear where the bushing goes. Once I get the new bearing if it’s too much I’m just going to sleeve it. The other alternative for those of you who don’t have a machine shop is to have it metal...
  5. Garygin

    Help on purchase twin 225s

    Hey chawk_man. I have a 2002 225 hp. The vertical shaft from the water pump with the spline end. It goes through the extension case and in that case I can see what looks like a bronze split bushing . Is that something that Honda made a change on? I can’t seem to find it anywhere. Also what does...
  6. Garygin

    Honda 225 max rpm 3500

    I will check this weekend and see what I have . Thanks again
  7. Garygin

    Honda 225 max rpm 3500

    My prop is a 14 X 17
  8. Garygin

    Honda 225 max rpm 3500

    Thanks for all of your help. I will check the pitch on the prop tomorrow
  9. Garygin

    Honda 225 max rpm 3500

    Well thanks for the info. When you say dry weight 3500 what exactly do you mean? What do you think the pitch should be on the prop. At 3500 I was at 32 mph
  10. Garygin

    Honda 225 max rpm 3500

    It’s on a 22’ Grady seafarer. Not sure of the pitch on the prop
  11. Garygin

    Honda 225 max rpm 3500

    Yes it is new to me. I had to do some touch up on the engine , all filters and water separators etc. I ran it yesterday for the first time after fixing everything. It ran great , but from what I’ve read it should run up to 5000 rpm.
  12. Garygin

    Honda 225oil leak

    I have a Honda 225 2002. I have an oil leak somewhere above the lower unit. It is coming out where the two 14 mm bolts are that connect the steering arm. It seems to be coming out from where the oil pan is. Any ideas on what to check ? Thank you, Gary
  13. Garygin

    Honda 225 max rpm 3500

    Ok . So I have a 2002 Honda 225 outboard. The engine runs great. Thanks to chalkman , what a great help. Replaced all filters.EVERYTHING is clean. Then engine runs great up to 3500. It just won’t go over 3500. Any help would be greatly appreciated. Thanks in advance
  14. Garygin

    2002 NMEA cable

    Looking for information on weather a 2002 Honda 225 can be connected for NMEA . Any help would be greatly appreciated. Thanks Gary
  15. Garygin

    Tilt trim sending unit

    Hi jgmo. Well I did everything you suggested. It all checked out perfectly. I do have a service manual, but I can tell you , you were more of a help than the manual. After I checked everything I decided to call Auto Meter and ask them what they thought. Long story short they said that the gauge...
  16. Garygin

    Tilt trim sending unit

    Hey jgmo! Thanks for the info. I checked everything and it is right where it should be . Still doesn’t work. The question I have for you is , when I turn the key on and check voltage and such I’m getting continuity between the signal wire and ground at the gage. Is that right? Thanks Gary
  17. Garygin

    Tilt trim sending unit

    Hey ! Thanks so much for the info. I will check it out and see. Thanks again, Gary
  18. Garygin

    Tilt trim sending unit

    I just put a trim sending unit on today. When I hooked it up it just pegs the needle on the gage. Any suggestions on what to look for? Thanks for your help Honda 225
  19. Garygin

    ~ 2006 Honda BF225 Extreme bucking around 2700 RPM

    I have the issue of my 225 starts instantly, idles fine . When I get to about 2000 rpm it fall on its face. Doesn’t die but goes back to idling. Took the vst out checked EVERYTHING. The only thing I could find is the hp fuel filter was collapsed. Fuel lines replaced, racor replaced. Haven’t had...
View older results
Back
Top