Logo
FULL SITE MENU

Search results

  1. K

    Tilt trim relay bracket

    It still works just at times it doesn't. Seems as there is a loose wire causing it to arc and sometimes not work. Pop the engine cowl off and move it around and it works.
  2. K

    Tilt trim relay bracket

    I'm going to take it off and look it over really well tomorrow, I'll let you know what I find.
  3. K

    Tilt trim relay bracket

    I tried that with no luck
  4. K

    Tilt trim relay bracket

    Virginia
  5. K

    Tilt trim relay bracket

    I can't find the replacement bracket says no longer available.
  6. K

    Tilt trim relay bracket

    This is a pic of the back of my relay bracket. It's melted....
  7. K

    Tilt trim relay bracket

    I have noticed that my relays for tilt and trim have been arcing. Often the relays will stop working and just click. I can press on them and I have power again. I've noticed arcing so I suspect I have a wire touching. Not much slack to even pull it out and get a good look. I'm trying to...
  8. K

    Engine stalls in gear!

    Just rebuilt carbs and still stalls in water going into gear. I'm going to need a compression tester now. Are the ones on Amazon or the ones at Harbor Freight ok?
  9. K

    Fireworks at the Relays!

    So I just noticed that my tilt-trim relays are arcing here and there.... They are pressed in as far as they will go. If I hold them in and hit the buttons then I don't get any arcing. Anyone ever had this happen?
  10. K

    Engine stalls in gear!

    I suppose I'll go ahead and rebuild the carbs with a rebuild kit and see if that fixes or improves.
  11. K

    Engine stalls in gear!

    It comes off the side not the top. It's just below the cowl.
  12. K

    Engine stalls in gear!

    I'm referring to the remote control shifter at the helm the shifts the outboard into gear.
  13. K

    Engine stalls in gear!

    I don't have a compression tester but the tell tale hose is on the starboard side of engine. The engine ran the boat with previous owner without stalling in gear. I just replaced the throttle controller and the idle isn't the same.
  14. K

    Engine stalls in gear!

    I have my outboard running well, starts easy and when I put her in the lake and shift into gear it dies. I tried many attempts after letting it warm up. It runs and idles good but dies under load after going in gear. Outboard is a 1990 70 hp Evinrude. I did put it in gear in the driveway on...
  15. K

    Can't get this idle adjusted!!

    Also if I lift up the fast idle lever to start engine and try to close lever, it doesn't close all the way and still idles way to high!
  16. K

    Can't get this idle adjusted!!

    So previous owner just replaced the throttle cable and I'm trying to get it dialed in. When you pull the control stick back to close it never closes all the way. I can move it back closed manually I just need to get this cable adjusted to do it. I have some pics of my throttle cam and cam...
  17. K

    She just won't QUIT!!

    I connected the two wires and that did the trick! I was thinking maybe the cowl cover could have cut the wire possibly by taking it on and off but I really think it was cut by previous owner.... makes no sense. The good news is that did the trick, thank you for your help!
  18. K

    She just won't QUIT!!

    I just found where this black/yellow was originally connected but apparently cut.
  19. K

    She just won't QUIT!!

    I'm wondering why it's been cut! Can I test by stripping the end and running from this cut wire to my key switch? I'm also thinking there must have been a short in the original wire and a bypass had been done for kill circuit. I don't remember seeing any extra wire but hard to tell...
  20. K

    She just won't QUIT!!

Back
Top