Logo

4.3 Mercruiser - randomly dies

Yep agreed with all your points. I have a lot of spares too
2 carbs
2 fuel pumps
starter
alternator
PS pump
Prestolite points distributor
transom assembly that I have already harvested a number of parts from
outdrive that probably needs a rebuild
and many OMC Cobra spares, because you can't just go to a dealer and buy them like a Merc or Volvo Penta garage is full of stuff. If I ever sell the boat, I will have to open an eBay store!

Normally I run this:
View attachment 38014
little bit of oxidation on a 38 year old Quadrajet

but I also have these just in case lol:
Marine Holley and Edelbrock
View attachment 38015
My 1992 still looks pristine. Granted, we only took the boat in salt water a few times to see the Blue Angels from under the Golden Gate bridge. But a couple of times a year I sprayed the carb and all the electrical stuff with WD40. Never had any problems even with crimp connections that weren't even sleeved.
 
You are clearly a wise man based on your posts and your hardware stockpile!


Been doing this stuff for a long time. All my friends have boats as well as their adult children and almost all are carbed mecruiser V8 or V6.

I also do some numbers matching Holleys and Rochesters for 60's 70's muscule cars (Nova, Camaro, Chevelle) for a friend who buys/restores/sells the cars.

He has in his garage right now a 1970 Chevelle Red with two black stripe modle with a original LS6 454 4 speed 100% ALL original except paint. Build sheet and Build O Plate. California car never been molested in any way. But the 1969 Camaro next to it is a 396 HP model with 375 hp and that Holley 780 CFM, I just rebuilt two weeks ago.
 
Last edited:
Fresh water boating where you keep it on a trailer is a whole different story than mooring or slipping a boat in salt water.
Everything will show some corrosion, and it's common to find oxidation on terminals
That said, I haven't had much trouble with the electrical system just a few things, I am going to change the old fuse block under the dashboard that still has glass fuses over the winter.
The OMC Cobra drive/transom assembly looks like any other salt water boat that's moored, it needs to be totally stripped down and repainted, but as far as shifting etc, it works just fine. Basically all I have had to do to it is regular maintenance, pulling it each season, replacing the bellows when needed etc. Only repairs have been rebuilding the trim rams (actually had to replace the ram rods due to corrosion), water pump seal, bellows 2x, that's it, 24 years of use in salt water. I also changed the steering actuator due to leaks, I have a couple of spare ones too lol.
The biggest thing in salt water is exhaust systems, you have to change them eventually, or else you can get leaks into the cyls, I can check these (OMC/Volvo center riser style) by using an endoscope camera via one of plugs on the top of the exhaust elbow. This last set are still good, 7 seasons in salt water so far. I also pull off the rubber hoses and check the condition of the outlets of the elbows, where the corrosion usually starts.
Then there's trailers, here the only things that last are galvanized or aluminum, no painted trailers.
Here's what the inside of the exhaust elbow looks like:
exhaust staboard side.jpg


I think my old engine lasted this long (1988 original short block, replaced heads in 2017) because I filled it with antifreeze after draining.
I use Sierra brand PG antifreeze mixed to provide -30*F protection (overkill for here) I like this stuff better than what you typically find because it is good enough to use as engine coolant unlike the storage only type antifreezes....
antifreeze & refractometer.jpg
 
I think some of the electrical hardware on boats isn't really up to the demands of a marine environment. So the more electronics we have the more potential for problems with more failure points. Case in point, the small relays used, the unprotected terminals, on both fuel pump relays and tilt n trim relays. Even the relay harness for headlights I installed on one of my Jeeps has a gasket to protect the terminals of the relay! This should be a must on any marine engine. On my old 1988 OMC, the trim relays are the old large style relays with very large terminals, like a Ford starter relay. I also like carbed engines because having a carb gives you some real advantages:
repairs are cheaper, rebuild kits, even the best quality ones, are not expensive
due to the popularity of the collector car hobby in the USA, we can get carb parts very easily, and brand new Holley and Edelbrock carbs are available at reasonable prices. I can even get all the parts I need for a Rochester Quadrajet that hasn't been made since 1990 with no real problem.
And if your original carb can't be rebuilt due to corrosion, you can just replace it.

I have seen Packard connectors (the type with a light green rubber seal) of the type used in GM vehicles and they work well- all of the sensors and control modules use these in most EFI applications. Can they leak? Sure, under the right conditions but relays didn't use the sealed sockets until fairly recently. Now, a lot of harnesses have Deutch connectors, but I don't know which has been found to be more resistant to moisture ingress.

I'm still amazed by the fact that most splices in the boats I worked on weren't sealed in any way. I find that totally irresponsible. Do the Heat N Seala terminals cost more? Yes, but they also prevent warranty claims, although the environment makes a difference and I wouldn't be surprised if boat manufactures deny claims in salt environments.
 
Back
Top