Logo
FULL SITE MENU

Latest activity

What's new New posts Latest activity
  • J
    jgmo replied to the thread Bf 200.
    Hi, 2008? Only 500 hours? Sorta/kinda sounds like they couldn't figure out the problem and just parked it for 18 years? Do you know...
  • B
    boscoe replied to the thread Tach not working.
    No, the loss of a tachometer signal is not common. At all. If YDIS is displaying RPM then the ECM is getting the message. Why you are...
  • R
    Redden3056 replied to the thread 02 DF70 random oveheating.
    Ok. So I replaced the poppet and the thermostat. When I opened the thermostat housing to replace, the old one was stuck OPEN. I...
  • K
    kevinj replied to the thread I have a 2006 Johnson 115 hp outboard that leaks oil at the prop shaft.
    Agreed, likely normal 2-stroke exhaust oil. You could possibly have weak spark due to worn spark plugs. Make sure you have a fresh set...
    • 1780330264361.png
  • R
    racerone replied to the thread 1990 Johnson 110 VRO - Trouble Issue.
    Was it stored with fuel in the carburetors ?----Also do a compression test.---Post the actual values here.---What fuel pump is on it now?
  • T
    Tomhop posted the thread Bf 200 in Honda Outboard Forum.
    Looking to buy a boat that has a 2008 BF200 on it. Honda dealer report says it has 500 hours and 20 overheat alarms. Is this a...
  • A
    Alex1019 posted the thread 1990 Johnson 110 VRO - Trouble Issue in Johnson Evinrude Outboard Forum.
    Hello, I am new to boats and I have a few questions. I have a 1990 Johnson 110 VRO model; however the motor does not want to turn on...
  • makomark
    makomark replied to the thread 283 rocker studs.
    if one stud has come free, the others are likely to be in a similar situation. Pinning a stud will keep it from coming out but the...
  • S
    Squidrow posted the thread 2022 DF 200 in Suzuki Outboard Forum.
    Multi Functin Guage is not powering up....have checked the power wire fuse feeding the guage, no power...key on no pwer on the grey wire...
  • N
    NSDON replied to the thread BF225 - Tips for removing propshaft holder?.
    I also use a block of hardwood on things like this on the area of the joint and tap it around the circumference, it can shock the locked...
  • T
    titaniumfemur replied to the thread 283 rocker studs.
    Thanks for the recommendation. Can you explain a little further how pinning doesn't help. I thought it essentially prevented them from...
  • R
    rvaughnp replied to the thread 91’ OMC 5.0 motor w/ 4.3 stern. Spun Gimble..
    Spent a few hours on the water. Pulled upper gear case cover and only lost about 1/2” of gear oil. Will pull the SD this coming weekend...
  • makomark
    makomark replied to the thread 283 rocker studs.
    Threaded studs eliminates the issues with the pressed in studs....pinning them doesn't. I would do all of them as the others are likely...
  • M
    mike@holden replied to the thread Tach not working.
    I will need to get a multi meter that reads hz. I hooked up the faria tach back probed green wire at ecm and probed 12 + and 12 - at...
  • B
    boscoe replied to the thread Tach not working.
    14.5 volts for that model is not excessive. Rectifier is not in the loop with respect to the tachometer signal for that model motor...
Show older items
Back
Top