Quicksilver Marine Parts Catalog
- Contents
- Pre-1988 Mariner
- Mercury & Mariner
- Carburetor Kits
- Fuel Pump Repair Kits
- Ignition Keys
- Ignition Parts (2-Stroke)
- Ignition Parts (4-Stroke)
- Lower Unit Gearcase Seal
- Pistons
- Oil Filters
- Powerhead Gasket Sets
- Rod Main Bearings
- Solenoid Relay (2-Stroke)
- Solenoid Relay (4-Stroke)
- Spark Plugs (2-Stroke)
- Spark Plugs (4-Stroke)
- Stators
- Thermostat Kits
- Water Pump Parts (2-Stroke)
- Water Pump Parts (4-Stroke)
- Mercruiser
- Engine Parts
- View All »
- Alternators
- Camshafts, Bearings, Lifters & Push Rods
- Carburetors
- Connecting Rod Bearings
- Crankshaft Bearings
- Distributor Assembly & Components
- Distributor Gears
- ECMs, Coils, Wires & Spark Plugs
- Engine Couplers
- Engine Gaskets
- Exhaust Manifolds & Elbows
- Flame Arrestors
- Fuel Coolers
- Fuel Injection Components
- Fuel Pumps & Filters
- Ignition Tune-up Kits
- Intake & Exhaust Valves
- Oil Coolers
- Oil Pumps & Components
- Piston Rings
- Pistons
- Rocker Arms & Hardware
- Starter Parts
- Starters & Solenoids
- Thermostats, Housings & Covers
- Timing Chains & Gears
- Valve Caps, Springs & Keepers
- V-Belts & Serpentine Belts
- Water Hoses—Engine Supply
- Water Hoses—Exhaust Cooling
- View All »
- Transom & Drive Parts
- View All »
- Bearing Carriers
- Bellows
- Drive Shaft Housing & Sterndrive Units
- Drive Shaft Housing Bearings
- Drive Shaft Housing Gears
- Gear Case Bearings
- Gear Case Gears
- Gear Case Seals
- Gear Case Shafts
- Gear Case Shims
- Gimbal Bearings
- Installation Gaskets
- Trim Cylinders
- Trim Cylinder Hardware
- Trim Cylinder Hoses
- Universal Joints (U-Joints)
- Water Pump Impellers & Kits
- View All »
- Engine Parts
- Page Numbers
FUEL SYSTEM
9 FT. FUEL LINE ASSEMBLY
BULK FUEL LINE
Low Permeation hose 9 ft. (2.74 m) 5/16" line with primer bulb, 2 snap clamps, and
Low Permeation hose, 5/16 in. (8 mm) I.D. x 100 ft. (30.5 m) spool.
no end connectors.
Fits fuel line assemblies for delivering fuel from the fuel tank to the engine fuel
Standard universal 5/16" (8 mm) I.D. fuel line can be adapted to many uses by
connector.
adding different connectors as desired. This assembly may be used in all
applications not governed by US‑EPA 2011 regulations.
Low Permeation hose, 3/8 inch (9.5 mm) I.D. x 100 ft. (30.5 m) roll.
12 FT. FUEL LINE ASSEMBLY
PRIMER BULB ASSEMBLY
Low Permeation hose 12 ft. (3.66 m) 5/16" line with primer bulb, 2 snap clamps,
and no end connectors.
Standard universal 5/16" (8 mm) I.D. fuel line can be adapted to many uses by
adding different connectors as desired. This assembly may be used in all
applications not governed by US‑EPA 2011 regulations.
Quicksilver Branded, Box Point of Sale Packaged.
12 FT. FUEL LINE ASSEMBLY
Using materials resistant to the chemistry of today's fuels, this bulb is designed to
remain pliable longer. Two hose clamps are included.
For use with our gray color, 5/16 in. (8 mm) I.D. fuel line & 3/8" I.D. fuel line. This
bulb may be used in all applications not governed by US‑EPA 2011 regulations.
Priced individually, sold @ multiples of 4
Quicksilver Branded, Box Point of Sale Packaged.
PRIMER BULB ASSEMBLY
Low Permeation hose has double sealed quick connect type fitting on tank end,
and standard quick connect fitting on engine end. Primer bulb is included in this 12
ft. (3.66 m) assembly.
Fits Force 40 hp. and larger (1993 and Newer), Force 9.9/15/25 hp. (1998) and all
Mercury/Mariner outboards using clip‑on type disconnects at both tank and engine
ends. This assembly may be used in all applications not governed by US‑EPA
2011 regulations.
Quicksilver Branded, Box Point of Sale Packaged.
FUEL LINE ASSEMBLY- UNIVERSAL
For use with our 1/4 in. I.D. (black) fuel line. This bulb may be used in all
applications not governed by US‑EPA 2011 regulations.
Quicksilver Branded, Box Point of Sale Packaged.
Fuel hose (only). CE certified 5/16" I.D. (.315 in. 8 mm) fuel line with no
connectors. 9 ft. (2.74 m) Premium fuel line for custom manufacturing fuel line
assemblies.
524