Logo
FULL SITE MENU

Search results

  1. T

    Pressure test

    I have 2013 mercury 3 cylinder 75HP fuel and oil injection that has 100 psi is this good or bad
  2. T

    Rebuilt 4.3 carburetor engine taking on water

    I have a total rebuilt 4.3 taking water in all six cylinders. Runs great with no water running through engine. run water with engine not running all 6 cylinders fill with water. Thanks milton
  3. T

    This is unreal

    Got a 1986 mercury V6 inboard that was completely rebuilt engine cranked and ran smooth but had steam coming out of exhaust got water hooked direct to lower water inlet hose with water ruining and engine not all six cylinder are filling with water ????? Thanks Milton
  4. T

    need a mercruiser 4.3 local mechanic Auburn Ga 30011

    need a mercruiser 4.3 local mechanic Auburn Ga 30011 who makes house calls
  5. T

    what electric fuel pump do I need.

    I Have mercruser 4.3 that I need to replace the electric fuel pump, It is carb engine. manual says I need 3.5 5.5 psi All I can find is 8-10 psi Will this work and not flood engine, if so does anyone know where to get one that will work at a fair price Thanks
  6. T

    Inboard outboard power steering fluid

    What type power steering fluid is best for inboard outboard engine. Will regular power steering be OK Thanks
  7. T

    Manual fuel pump to electric fuel pump.

    need to know what oil pump switch to use for electric fuel pump N//O Thanks
  8. T

    Engine to tight

    bought a 4.3 v6 complete unassembled engine. all went good until I installed the pistons Gaped the rings and when I installed the piston the engine got tight. All rod bearing are .002 I have only installed 5 pistons and when I do I have to drive them down with a rubber mallet. Can not lust...
  9. T

    Starter testing out of boat

    Trying to test starter out of boat The starter has 4 wiring post on it, two large and 2 small. Can get it to run with direct 12 volts what are the two small post. I can not get nothing when I short either of the two small post to 12 volts. ????? Thsnks
  10. T

    4.3 v6 mercruiser exhuast 3"x3" coupling

    Any body know were I can find a 4.3 v6 mercruiser exhaust 3"x3" ID rubber coupling. All that I can find are 3 5/8" Thanks
  11. T

    4.3 V6 piston ring orientation

    My new rings do not have spot on them but 6 of them are angle cut on one side Any body know how they need to go on the piston Thanks
  12. T

    Rear balance shaft install tool

    looking for what tool or how to install rear balance shaft bearing. Thanks Milton
  13. T

    4.3 V6 balance shaft bearing spacer

    Can anyone tell me what the purpose of the spacer in the picture is for
  14. T

    Oil pressure relief valve

    Can some one tell me where the oil pressure relief valve is located on a chevy 4.3 V6 Thanks Milton
  15. T

    1997 4.3 V6 car to boat conversion

    I have a 1986 mercury 4.3 standard with cracked block I pick up a 4.3 V6 vortec out of a 1997 C10 throttle body and need to change to 4 barrel carb Will my intake from my original engine work, if not is there a adapter that will work with the intake I have. Thanks Milton
  16. T

    What engine do I have

    I have a 1986 wellcraft elite 185 V6 stern drive that has a cracked block and need to know what engine it has in it. Thanks
  17. T

    How do you tell if you r oil injection is working

    As the title says, How can you tell if the oil injection is working I bought a 2012 mercury that the old owner did not use is for some reason Milton
  18. T

    Totally confused ????

    Think I bought another headache. 1984 90hp 6 cylinder Mercury I can not find a + or - battery cable on this engine. How does the starter get power. Motor is still on the boat that it was running on. Tried to post picture but cant for some reason. Thanks Milton
  19. T

    Fuel pump question

    Should the fuel line from the fuel pump to carb hold pressure after you turn off the ignition. Been having with engine bogging down after about 1/3 throttle under a load so I hooked up a pressure tester on the fuel line that goes from the pump to the carbs. Could only get about two pounds of...
  20. T

    Looking for boat Mechanic around Auburn GA 30011

    Looking for shad tree boat engine Mechanic for a 1982 mercury 70 hp 3 cylinder. I am located in Auburn Ga 30011 about 5 miles from Winder Ga. Email [email protected] Phone 678 372 7697 Thanks Milton
Back
Top