Logo
FULL SITE MENU

Recent content by hcccs

  1. hcccs

    Starter plunger

    I tested the heating element inside with 12V and it got hot right away. Then I reassembled it tested again to se if the needle would move but it didn't. It was difficult to sense any heat from the ouside of the plastic body. There is a rod inside the "wax" chamber and when I pulled it out I saw...
  2. hcccs

    Starter plunger

    Thanks boscoe! Most helpful.
  3. hcccs

    Starter plunger

    This a starter plunger for a Yamaha 4-stroke 9.9 outboarder (6G81410A0100). I have taken mine apart thinking I could fix it but I can't really understand how it works Does anyone know how they work?
  4. hcccs

    What are these Yamaha parts?

    Thanks
  5. hcccs

    What are these Yamaha parts?

    On my Yamaha F9.9BM 6G9 S 008982 Z (1994) engine there are two canisters I can't identify. What are they?
  6. hcccs

    Yamaha 9.9 stalling

    I rebuilt the carburetor of my Yamaha F9.9BM (6G9 S 008982 Z 1994). It starts really easy but sounds like it's running on one cylinder and when I throttle up the slighest it stalls. I ran it again, wihout hood and when I put my thumb close to the carb intake it reved up. It seems like my thumb...
  7. hcccs

    What are those numbers?

    Are the variants interchangeable?
  8. hcccs

    What are those numbers?

    For my Yamaha 30DEO 6J8 L 455099 G (=1988) the lower end casing should be 6J8-45300-14-EK (I think). I've found one casing numbered 6J8-45300-10-EK. What are those extra "14-EK" and "10-EK"?
  9. hcccs

    Yamaha pulling outboard bearing carrier

    OK, good news. Thanks
  10. hcccs

    Yamaha pulling outboard bearing carrier

    Yamaha 30DEO 6J8 L 455099 G (=1988)
  11. hcccs

    Yamaha pulling outboard bearing carrier

    This YouTube video shows how to pull the bearing carrier. One thing that isn't shown is that, as I believe, the gear selector has to be removed first. Am I right here or not? If the gear selector needs to be removed first, what do I do if it is, as in my case, stuck and can't be moved?
  12. hcccs

    Yamaha 9.9 1984 in the water

    My Yamaha 9.9 was submerged in water (almost fresh) for 24 hours. I took it home, removed the plugs, sprayed cylinders with oil, emptied and refilled the engine and gear-house oil. I then put it in the sauna at 60°C for six hours. Not being able to start it I removed the carburetor and cleaned...
  13. hcccs

    Yamaha 25 hp leaking oil

    Yamaha 25 hp 30DEO 1988. I filled the lower unit with gear oil today and found that a lot was pouring out of the holes seen in the photo. What are those holes anyway and why are they leaking oil?
  14. hcccs

    Yamaha 25hp shift rod stuck

    My boat with Yamaha 25hp was left outside for a year and I took it home to look it over and run it. I couldn't move the gear shift lever so I removed the lower part and found that the shift rod is stuck. I can turn the propeller but not move the shift rod i any direction. I guess I have to take...
  15. hcccs

    Evinrude 15hp no start.

    I finally purchased new ignition cables and with the spark tester I get good solid sparks 3/8" long so that was perhaps part of the problem. I have replaced the fuel line both inlet-to-fuel pump and fuel pump-to-carburetor with transparent hoses so I can see how far the fuel gets when I press...
See more
Back
Top